Please consider a donation to the Higher Intellect project. See https://preterhuman.net/donate.php or the Donate to Higher Intellect page for more info.

Difference between revisions of "Macintosh PowerBook 170"

From Higher Intellect Vintage Wiki
Jump to navigation Jump to search
Line 1: Line 1:
  
 
=Video Repair=
 
=Video Repair=
<pre>
 
 
I've had several occasions to open PB170/180s, and it's quite easy for the
 
I've had several occasions to open PB170/180s, and it's quite easy for the
 
Video cable (a ribbon cable) inside to be pulled out on reassembly - the
 
Video cable (a ribbon cable) inside to be pulled out on reassembly - the
Line 15: Line 14:
 
antistatic surface and wristband to work with, and I think a T7 and T9 Torx
 
antistatic surface and wristband to work with, and I think a T7 and T9 Torx
 
screwdriver.
 
screwdriver.
 +
 
Remove the battery to begin with;
 
Remove the battery to begin with;
 +
 
There are 5 screws in the case -
 
There are 5 screws in the case -
 
a single T7 beneath the 'flap' at the rear of the machine (where ports are at);
 
a single T7 beneath the 'flap' at the rear of the machine (where ports are at);
Line 53: Line 54:
 
battery (your PRAM will be reset now, so checkout your Control Panels to
 
battery (your PRAM will be reset now, so checkout your Control Panels to
 
restore values).
 
restore values).
</pre>
 
  
 
=See Also=
 
=See Also=

Revision as of 22:38, 18 July 2019

Video Repair

I've had several occasions to open PB170/180s, and it's quite easy for the Video cable (a ribbon cable) inside to be pulled out on reassembly - the top half of the case has to be 'hinged' from the front of the machine, downward, while this raises the back, and induces tension in the ribbon cable. The wires also carry trackball/keyboard ADB info. You may need to push the connector back in. If the machine has been installed after manufacture with the 8Megs, and the Global Village hardware, chances are that other stuff got loosened too - maybe the HD power cable if the tech wasn't careful.

Opening the bigger PBs isn't too problematic, provided you have an antistatic surface and wristband to work with, and I think a T7 and T9 Torx screwdriver.

Remove the battery to begin with;

There are 5 screws in the case - a single T7 beneath the 'flap' at the rear of the machine (where ports are at); 4 x T9 screws in the case below.

Once these are removed, and the machine placed with the LCD display down, in the position you would normally type at, the top half of the case can be gently removed. You will probably have to be persistent here, because it's quite stiff; the rear edge will normally release OK, but there are little 'tabs' on the front edge that can only be disengaged by your teasing the front edge backward. It will release in time.

Now, you'll find the top case can pivot backward and you'll see the ribbon cable that is the video connector. It may need to be pushed firmly back into place. (though of course it may not be clear whether it was loose originally or due to the current disassembly!)

You could now either reassemble the Mac, or investigate further. If the latter, the whole top part of the case including the LCD display can be put to one side if you ease the video connector straight upward (there are not clips to hold it in, part of the problem really!). There's nothing related to the Motherboard or HD on this top section. Checkout the other connectors you can see, and make sure they're tight. (of course how far you're prepared to investigate is entirely up to you.)

Reassembly is the reverse of the above. It helps if you 'balance' the rear of the top part of the case on the row of ports at the back of the Mac (resting in particular on top of the SCSI connector) with the top case at about 45deg to the horizontal, as this will give you enough slack to plug the video connector back in. Then 'pivot' the lid downward, and slightly raise the rear edge (without yanking the cable free) to let you drop the front edge into its groove, where the tabs will hold it in place. Then drop the rear down again, and push it slightly - there will be a little resistance, but will click gently on the left hand side.

Shove the screws back in the lower case, then behind the flap. Replace the battery (your PRAM will be reset now, so checkout your Control Panels to restore values).

See Also