Please consider a donation to the Higher Intellect project. See https://preterhuman.net/donate.php or the Donate to Higher Intellect page for more info.

Macintosh SE/30

From Higher Intellect Vintage Wiki
Revision as of 14:53, 7 April 2019 by Netfreak (talk | contribs)
Jump to navigation Jump to search

Macse30.jpg
37554681 1010917015699852 8990290582676963328 n.jpg
35532587 395884160924146 4353219752752054272 n.jpg

A popular system for hobbyists due to the compact size and expansion capabilities. The SE/30 is powered by a Motorola 68030 at 16MHz with FPU. The system is known to support up to 128MB memory, though you will either need a 32-bit clean ROM or run with 32-bit addressing enabled in the software side.

Expansion

There is a single "SE/30 PDS" expansion port, though you are able to get creative with PDS adapters in order to fit multiple expansion cards inside the chassis. Ethernet is probably one of the most popular options, along with CPU accelerators.

Troubleshooting

Jittery Video

Description: This common problem is not mentioned on the RMS webpage. It's usually caused by problems in the 4 pin connector (marked "P5" on the analog card) interface between the analog card and the CRT yoke. One or more pins in the analog card connector develop bad solder joints. A bad solder joint can cause excessive heating which causes heat corrosion in the associated pins within the 2 connectors. The heat corrosion will cause discoloration of the white connector shells.

Repair:

  1. Verify that the lug of the black/white ground wire from the CRT neck video card is firmly screwed down.
  2. If it is loose, tighten the screw and retest before doing following steps.
  3. On analog card, remove old solder from all 4 pin connections and resolder all 4 pins.
  4. If there is connector discoloration: Identify which pin pair is closest to discoloration. Scrape down the male pin with sharp pointed xacto knife blade. Use tweezers or needle nose pliars to compress the female pin so that has tighter grip on male pin.

Replacement Tantalum Capacitors

REF DES   CAPACITANCE   VOLTAGE    CHIP CASE    REPLACEMENT    MANUFACTURER
         (microFarads)   (VDC)       CODE       PART NUMBER

              1.0         50 <--(ORIGINAL PART RATING)
              1.0         35          B         TAJB105K035R     AVX
C6            1.0         25          B         293D105X9025B2T  Sprague
              1.0         35          B         293D105X9055B2T  Sprague
              1.0         25          B         T491A105K025AS   Kemet
              1.0         35          B         T491B105M035AS   Kemet

C1,C3          47         16 <--(ORIGINAL PARTS RATING)
C4,C5          47         16          C         (Available)
C7,C8          47         16          D         293D476X9016D2T  Sprague
C9,C10         47         16          D         T491D476K016AS   Kemet
C12,C13        47         16          D         ECS-T1CD476R     Panasonic

Dimensions:
CASE     EIA       Length      Width
CODE     SIZE

 A       3216      0.126 "     0.063 "
                    3.2 mm      1.6 mm
 B       3528      0.138       0.110
                    3.5         2.8
 C       6032      0.236       0.126
                    6.0         3.2
 D       7343      0.287       0.170
                    7.3         4.3

Notes

Press the interrupt switch on the side of the computer and type dm 4082E853 20 into the message box and press return. This will return the message "WHAT ARE YOU STARING AT?"

Modifications

040et stack.gif030egs stack.gif

Gallery

See Also