Please consider a donation to the Higher Intellect project. See https://preterhuman.net/donate.php or the Donate to Higher Intellect page for more info. |
Monitors on SGI Machines
How to deal with and choose monitors on SGI machines.
13w3 to SVGA converter cables
Both Sun Microsystems and Silicon Graphics machines from a certain era use 13W3 connectors either on the monitor or the workstation. There have been reports of SUN cables not working with SGI machines and there are contradicting reports. To be safe use a SGI 13W3 cable, although the originator of this wiki entry has swapped a SUN Blade 1000 and Octane cable for kicks with Octane dealing with it but the SUN not. Your mileage may vary.
Sync on Green
Most SGI machines produce a sync on green signal (SOG). Many monitors will not handle this and either no picture or a green tinted display will occur.
Known good monitors
Manufacturer | Model | Description and notes | Confirmed on |
---|---|---|---|
SGI | 1600SW | O2s.Octane with MLA | |
Acer | |||
AL1916W LCD (1440x900), | O2 confirmed by Dr. Dave | ||
Balance | CM2019 (Model F192) | 19" 1280x1024 VGA/DVI LCD | Indy confirmed by darkninja |
Cornea | MP704 , | (17" 1280x1024 VGA only LCD), | O2 confirmed by tillin9 |
CMV | CT-720D | 17" LCD, | O2 confirmed by strandedinnz |
Dell | |||
2005FPW | O2 confirmed by lewis | ||
2001FP | 20.1" UXGA LCD (S-IPS true 24-bit), | O2 confirmed by MisterDNA | |
1800FP | 18.1" SXGA LCD (S-IPS true 24-bit), | O2 confirmed by MisterDNA | |
1901FP, | O2 confrimred by ramq | ||
1908FPc, | quoth "theodric": When I factory-reset the monitor, I got fuzzing @ 60Hz-- then I picked 72Hz and all was clear. Also works well @ 50Hz | O2 confrimred by theodric | |
2407wfp, | (24" 1920x1200 DVI/VGA), | O2 confirmed by tillin9 | |
2405FPW, | O2 confirmed by dangermouse | ||
Eizo | |||
FlexScan S1910, | O2 confirmed by Arabski | ||
FlexScan L567, | quoth "cicero": "The Eizo works out of the box with the O2. Colors are okay. This display doesn't support "Sync On Green" (SOG), so it uses the H/V sync signals outputed by the CRM gfx. Some vertical regions of the displayed image are a little blurred. You probably notice this effect when working in the shell." | O2 confirmed by cicero | |
Elements | EN-LM500/ Envision EN5100e 15" TFT, | (same panel marketed under at least those two names), only supports 1024x768 max resolution VGA, | confirmed by tillin9 |
Fujitsu Siemens | X140f | (@1024x768), | confrimred by ramq |
Gateway | VX900 | 18" CRT, | confirmed by akimmet |
HP | F1703 | 17" SXGA LCD (dithered 18-bit) (several versions made), | confirmed by MisterDNA |
IBM P70 17" CRT | |||
IC Power 17' & 19' LCDs, | O2 confirmed by zizban | ||
Iiyama | Vision Master Pro 17 | 17" CRT (both on HD15 and BNC inputs) | |
LaCie | 19 & 22 ElectronBlue IV, | (LaCie CRTs are rebadged Mitsubishi Diamondtrons). | O2 confirmed by fu |
LG Flatron L1952H, | O2 confirmed by cicero | ||
LG | 22LG3000 | 22 inch TV with HDMI and D-sub VGA inputs | Indigo2 via 13W3 adapter (1280x1024), Fuel via DVI-VGA or DVI-HDMI confirmed by ajw99uk |
Mitsubishi | Diamondtron RDF225WG 22", | (same as LaCie's ElectronBlue CRTs, specs ) | |
NEC | Multisync LCD 1770 NX, | quoth "cicero": Doesn't support SOG, so you have to "use a customized VGA cable (pin 11 - 15 removed) in order to force the display to use the SOG signal". | confirmed/hacked by cicero. |
NEC | Multisync LCD 1830 TFT, | confirmed by loonvf | |
NEC MultiSync | FP1370 (22 CRT), | confirmed by gaku | |
NEC | 1860NX | (18" TFT) - 1280x1024, DVI/VGA, | confirmed by tillin9 |
Nokia Multigraph | 449M | (15 CRT), but needs a hack/patch:
quoth "gaku" * Nokia Multigraph 449M (15 CRT) get a green tint, thus not fully SOG capable, but at least it's working and "almost" looking normal with an gamma-patch" applied as suggested by ... -> hindu <- |
confirmed by gaku |
Philips | 150S6FG/00 (15" TFT), | O2 confirmed by xc8 | |
Philips | 150 S4, (15" 1024x768 VGA only LCD), | O2 confirmed by tillin9 | |
Samsung | 950p, | O2 confirmed by zafunk, needs SOG activation | |
Samsung | 740N, | confirmed by hamei | |
Samsung | 153T | 15" LCD (dithered 18-bit), | confirmed by MisterDNA |
Samsung | 17GLi | 17" CRT, confirmed working with Indy using 13W3-HDB15 adapter. | confirmed by cris_adder |
Samsung | 172x, | confirmed by phrosty-boi | |
Samsung | SyncMaster 226BW, | confirmed by Glock | |
Samsung | SyncMaster 710V, | confirmed by Indyboy | |
Samsung | SyncMaster 900p | 19" CRT, Works very well with Indy and O2. Need to use only the RGB BNC connectors on monitor for SOG to work (i.e. do not use the HDB15 connector). | confirmed by cris_adder |
Samsung | SyncMaster 940BW | Tested WITH 13W3->HDDB15 adapter on Indy, I2(Extreme & Impact), O2(w/o adapter) and O2k+MXE | confirmed by Tesla |
Samsung | SyncMaster 940BF | Tested WITH 13W3->HDDB15 adapter on Indy, I2(Extreme & Impact), O2(w/o adapter) and O2k+MXE | confirmed by Tesla |
Sony | W700 | 24" CRT (Monitors #10, #11, #12), | confirmed by dion_b) |
Sony | GDM-400PS 19", | confirmed by gborce | |
Sony | SDM-P234 23" | aka Silicon Graphics F230-HD Flat Panel Display SGI p/n 013-4419-001; is recognized by /usr/gfx/gfxinfo as "Monitor 0 type: SNY 976" | Octane2 V12 via 13W3 Adapter using 1920x1200x60p vfo confirmed by Geoman |
Viewsonic | VG1921WM, | Quoth "hamei": "... works outta the box, blurry out of the box too, since native res on this is 1440 x 900 but O2 should be able to handle that if we get a custom vfo..." | O2 confirmed by hamei |
Octane
- Monitors [Sync-On-Green capable]
1. Dell 2407WFP 1920x1200_60 V8 or V12 graphics (13w3>HD15 connection) 2. Dell 2407WFP 1920x1200_60 V12 graphics w/DCD (DVI connection) 3. Dell P991 (works with 13w3 adapter with pins pulled) 4. SGI GDM-20D11 (standard 13w3 connection) 5. SGI GDM-20E21 (standard 13w3 connection)
Note: Monitors on the O2 Hardware Aggregator should work on the Octane as well (though a MLA will be needed with the 1600SW)
General comments (taken from nekochan posts)
1600SWs
The 1600SW is a widescreen flat panel video monitor from Silicon Graphics introduced in 1998. It won many awards after release and sold 54,000 units. It is notable for longevity, with used models still actively traded on eBay a decade later, despite the difficulty of adapting the monitor to run with modern video cards, due to the 1600SW's OpenLDI video interface.
Formac sold the same monitor bundled with its own OpenLDI graphics adapter as Formac ProVitron 18/500. Radius sold the monitor as the Article which differed mainly in having a translucent white case and a conventional mount. SGI sold the monitor primarily under Model #AM173Y01.
The 1600SW was revolutionary for its time, featuring a 17.3 inch diagonal wide screen panel in a market then dominated by CRT monitors. The 1600SW had a 16:10 aspect ratio (referred to by SGI as SuperWide) with a resolution of 1600 x 1024 pixels. The refresh rate was 60 Hz in 24-bit color and 110 dpi (which makes for a smaller dot pitch than most competitive monitors). The 1600SW shared the same styling motif as the SGI Visual Workstation 320, 540 and O2, with a unique (and troublesome) off-center mount. The display won a dozen international awards and despite its age, it still compares well to modern displays produced a decade later. At introduction the 1600SW cost in the neighborhood of $2500.
Complete list of PCI Video Cards with an 1600SW connector
- Formac ProFormance 3 (special version with OpenLDI)
- Number Nine Revolution IV (special version with OpenLDI)
- 3D Labs Oxygen VX1-1600SW
Monitor switches for OpenLDI
There is a 4-way monitor switch by Dr. Bott called MoniSwitch Pro LDI that allows sharing OpenLDI display among 4 computers, each of which must be equipped with an OpenLDI graphics adapter.
Adapting the 1600SW to Modern Video Cards
OpenLDI is rarely used today, as all popular home and office LCD panel monitors use a Digital Visual Interface (DVI) or VGA standard connector. There are several companies that make adapter boxes which allow continued use of these older displays. All of these adapters were developed for the 1600SW monitor:
- SGI Multilink Adapter (VGA or DVI) (discontinued)
- Dr. Bott SGI-Saver (DVI) (discontinued)
- PIXsolution PIX-Link 1600SW (DVI) (discontinued)
- GFX-1600SW sold by Niktec (DVI adapter, in passive PCI form factor, also sold built in to 1600SW monitors)
SGI referred to video cards that support the 1600SW's 1600 x 1024 resolution as Super Wide Savvy. Most modern cards have no trouble with this resolution, but on PC based machines, problems and screen distortion can exist during system boot. Apple Macintoshes boot directly into the proper resolution. Thus, with a little work, the 1600SW can be adapted to almost any modern computer.
PIX-Link
Multilink Adapter
Main article MLA
Multi-Link Adapter (for 1600SW)
Opening a MLA from packaging:
The box had been opened before I got it. Whether it was used at some point or not I can't be certain but the MLA is certainly in excellent, like-new condition. The cardboard box for the power supply had been opened at some point, but the permanently attached cord could easily be in the factory twist ties. The manufacturer for that PSU is SYN Electronics Company, Ltd, whose model number is SYS2011-4012 Rev B, and has "SGI P/N 9350836" also on it's label. Output is listed as +12V at 3.33 amps.
There are three video cables included, and all cables bagged together appear to bear the SGI part number 013-3066-001. One cable is DVI-D male to DVI-D male, and the second is DVI-I male to HD15 male. The last cable is apparently a "DFP" cable - on one end it's DVI-D male, but on the other it looks like a half-width version of the LVDS connector used by the 1600SW and other components.
The MLA I bought was generating hissing noise from one of capacitors, and I saw distortion lines on the screen, replacing capacitors solved both issues. See below for details.
Repair
Reporting full success, the capacitors are: Sanyo OS-CON 6SVP220M and 16SVP100M, I had no trouble ordering perfectly matching ones from http://www.logic-d.net/ (Japanese), it cost me some 147 and 273 JPY respectively a piece (ordered 3 of each just in case). Datasheets (in Japanese) are here: http://www.edc.sanyo.com/pdf/oscon/J32_33.pdf (the form factor matching the ones from MLA is F8).
Replaced them just now and the monitor works flawlessly, no hissing noise, and no noise lines in the picture either.
Looking at the board closely, it seems it may be possible to mod the MLA to accept ordinary 5V (with enough current) and simply get rid of all those capacitors, voltage regulators etc. I'm pretty sure there's no special reason for those other than being able to use the same power supply as in 1600SW...
It also makes me wonder what is the second power socket for - it's not soldered anywhere, but I checked and the respective pins are short with the same pins in the working one... (for a moment I thought that may have been direct 5V input - but it doesn't seem so).
One important point - my cheapo (sparkfun) 30W soldering iron was not really able to melt the existing solder - it's very likely SGI used lead-free solder with some relatively high melting point (could be even 20C above ordinary). So even though my soldering works I will need to resolder them again with better iron to ensure good contact (I have Weller stashed somewhere in my office so this won't take long). Also, the original capacitors are soldered ALL THE WAY along the contact pins (underneath too), so depending on your iron you may simply end up ripping part of it away from the board - and with an ordinary soldering method you will not be able to resolder it in exact same way (unless you have SMD kit).. The original capacitors have this little (red in my case) glue which holds them during manufacturing process - this one can be scraped off easily with any sharp object, you don't really need to apply any new glue, but it is helpful if the capacitor doesn't move while you solder