Please consider a donation to the Higher Intellect project. See or the Donate to Higher Intellect page for more info.

The Beowulf HOWTO

From Higher Intellect Vintage Wiki
Revision as of 14:30, 29 July 2020 by Netfreak (talk | contribs) (Created page with "<pre> The Beowulf HOWTO Kurt Swendson <[email protected]> 2004-05-17 Revision History Revision 1.0...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
The Beowulf HOWTO

Kurt Swendson

<[email protected]>

Revision History                                                             
Revision 1.0            2005-01-08                                           
first official release                                                       
Revision 0.9            2004-05-17             Revised by: 01                
initial revision                                                             

This document describes step by step instructions on building a Beowulf
cluster. This is a Red Hat and LAM specific version of this document.

Table of Contents
1. Introduction
    1.1. Copyright and License
    1.2. Disclaimer
    1.3. Credits / Contributors
    1.4. Feedback
2. Definitions
3. Requirements
4. Set Up The Head Node
    4.1. Hosts
    4.2. Groups
    4.3. NFS
    4.4. IP Addresses
    4.5. Services
    4.6. SSH
    4.7. MPI
5. Set Up Slave Nodes
    5.1. Base Linux Install
    5.2. Hardware
    5.3. Post Install Commands
    5.4. SSH On Slave Nodes
    5.5. NFS Settings On Slave Nodes
    5.6. Lilo Modifications On Slave Nodes
6. Verification
7. Run A Program

1. Introduction

This document describes step by step instructions on building a Beowulf
cluster. After seeing all of the documentation that was available, I felt
there were enough gaps and omissions that my own document, which I believe
accurately describes how to build a Beowulf cluster, would be beneficial.

I first saw Thomas Sterling's article in Scientific American, and immediately
got the book, because its title was "How to Build a Beowulf". No doubt, it
was a valuable reference, but it does not walk you through instructions on
exactly what to do.

What follows is a description of what I got to work. It is only one example -
my example. You may choose a different message passing interface; you may
choose a different Linux distribution. You may also spend as much time as I
did researching and experimenting, and learn on your own.

1.1. Copyright and License

This document, The Beowulf HOWTO, is copyrighted (c) 2004 by Kurt Swendson.
Permission is granted to copy, distribute and/or modify this document under
the terms of the GNU Free Documentation License, Version 1.1 or any later
version published by the Free Software Foundation; with no Invariant
Sections, with no Front-Cover Texts, and with no Back-Cover Texts. A copy of
the license is available at []   http://

Linux is a registered trademark of Linus Torvalds.

1.2. Disclaimer

No liability for the contents of this document can be accepted. Use the
concepts, examples and information at your own risk. There may be errors and
inaccuracies which could damage to your system. Though this is highly
unlikely, proceed with caution. The author(s) do not accept responsibility
for your actions.

All copyrights are held by their by their respective owners, unless
specifically noted otherwise. Use of a term in this document should not be
regarded as affecting the validity of any trademark or service mark. Naming
of particular products or brands should not be seen as endorsements.

1.3. Credits / Contributors

Thanks to Thomas Johnson for all of his support and encouragement and, of
course, for the hardware without which I would not have been able to even

Thanks to my lovely wife Sharron for her understanding and patience during my
many hours spent with "the wolves".

The original Beowulf HOWTO by Jacek Radajewski and Douglas Eadline.

1.4. Feedback

Send your additions, comments and criticisms to <[email protected]>.

2. Definitions

What is a Beowulf cluster? The authors of the original Beowulf HOWTO, Jacek
Radajewski and Douglas Eadline, provide a good definition in their document:
"Beowulf is a multi-computer architecture which can be used for parallel
computations. It is a system which usually consists of one server node, and
one or more client nodes connected together via Ethernet or some other
network". The site [] lists many web pages
about Beowulf systems built by individuals and organizations. From these two
links, one can be exposed to a large number of perspectives on the Beowulf
architecture, and draw his / her own conclusions.

What's the difference between a true Beowulf cluster and a COW [cluster of
workstations]? Brahma gives a good definition:[

If you are a "user" at your organization, and you have the use of some nodes,
you may still do the instructions shown here to create a cow. But if you
"own" the nodes, that is, if you have complete control of them, and are able
to completely erase and rebuild them, you may create a true Beowulf cluster.

In Brahma's web page, he suggests you manually configure each box, and then
later on (after you get the feel of doing this whole "wolfing up" procedure),
you can set up new nodes automatically (which I will describe in a later

3. Requirements

Let's briefly outline the requirements:

  * More than one box, each equipped with a network card.
  * A switch or hub to connect them
  * Linux
  * A message-passing interface [I used lam]

It is not a requirement to have a kvm switch, [you know, the switch to share
one keyboard, video, and mouse between many boxes], but it is convenient
while setting up and / or debugging.

4. Set Up The Head Node

So let's get "wolfing." Choose the most powerful box to be the head node.
Install Linux there and choose every package you want. The only requirement
is that you choose "Network Servers" [in Red Hat terminology] because you
need to have NFS and ssh. That's all you need. In my case, I was going to do
development of the Beowulf application, so I added X and C development.

It is my experience that you do not actually need NFS, but I found it
invaluable for copying files between nodes, and for automating the install
process. Later in this document I will describe how you can run a simple
Beowulf application without the use of NFS, but a more complex application
may use NFS or actually depend upon it.

Those of you researching Beowulf systems will also know how you can have a
second network card on the head node so you can access it from the outside
world. This is not required for the operation of a cluster.

I learned the hard way: use a password that obeys the strong password
constraints for your Linux distribution. I used an easily typed password like
"a" for my user, and the whole thing did not work. When I changed my password
to a legal password, with mixed numbers, characters, upper and lower case, it

If you use lam as your message passing interface, you will read in the manual
to turn OFF the firewalls, because they use random port numbers to
communicate between nodes. Here is a rule: If the manual tells you to do
something, DO IT! The lam manual also tells you to run as a non-root user.
Make the same user for every box. Build every box on the cluster with that
same user and password. I named that non root user "wolf".

4.1. Hosts

First we modify /etc/hosts. In it, you will see the comments telling you to
leave the "localhost" line alone. Ignore that advice and change it to not
include the name of your box in the loopback address.

Modify the line that says: wolf00 localhost.localdomain localhost                      now say: localhost.localdomain localhost                                    

Then add all the boxes you want on your cluster. Note: This is not required
for the operation of a Beowulf cluster; only convenient, so that you may type
a simple "wolf01" when you refer to a box on your cluster instead of the more
tedious wolf00                                                 wolf01                                                 wolf02                                                 wolf03                                                 wolf04                                                         

4.2. Groups

In order to responsibly set up your cluster, especially if you are a "user"
of your boxes [see Definitions], you should have some measure of security.

After you create your user, create a group, and add the user to the group.
Then, you may modify your files and directories to only be accessible by the
users within that group:
groupadd beowulf                                                             
usermod -g beowulf wolf                                                      

...and add the following to /home/wolf/.bash_profile:
umask 007                                                                    

Now any files created by the user "wolf" [or any user within the group] will
be automatically only writeable by the group "beowulf".

4.3. NFS

Refer to the following web site: [

Print that up, and have it at your side. I will be directing you how to
modify your system in order to create an NFS server, but I have found this
site invaluable, as you may also.

Make a directory for everybody to share:
mkdir /mnt/wolf                                                              
chmod 770 /mnt/wolf                                                          
chown wolf:beowulf /mnt/wolf -R                                              

Go to the /etc directory, and add your "shared" directory to the exports
cd /etc                                                                      
cat >> exports                                                               
/mnt/wolf (rw)                                   
<control d>                                                                  

4.4. IP Addresses

My network is 192.168.0.nnn because it is one of the "private" IP ranges.
Thomas Sterling talks about it on page 106 of his book. It is inside my
firewall, and works just fine.

My head node, which I call "wolf00" is, and every other node is
named "wolfnn", with an ip of + nn. I am following the sage
advice of many of the web pages out there, and setting myself up for an
easier task of scaling up my cluster.

4.5. Services

Make sure that services we want are up:
chkconfig -add sshd                                                          
chkconfig -add nfs                                                           
chkconfig -add rexec                                                         
chkconfig -add rlogin                                                        
chkconfig -level 3 rsh on                                                    
chkconfig -level 3 nfs on                                                    
chkconfig -level 3 rexec on                                                  
chkconfig -level 3 rlogin on                                                 

...And, during startup, I saw some services that I know I don't want, and in
my opinion, could be removed. You may add or remove others that suit your
needs; just include the ones shown above.
chkconfig -del atd                                                           
chkconfig -del rsh                                                           
chkconfig -del sendmail                                                      

4.6. SSH

To be responsible, we make ssh work. While logged in as root, you must modify
the /etc/ssh/sshd_config file. The lines:
#RSAAuthentication yes                                                       
#AuthorizedKeysFile .ssh/authorized_keys                                     

...are commented out, so uncomment them [remove the #].

Reboot, and log back in as wolf, because the operation of your cluster will
always be done from the user "wolf". Also, the hosts file modifications done
earlier must take effect. Logging out and back in will not do this. To be
sure, reboot the box, and make sure your prompt shows hostname "wolf00".

To generate your public and private SSH keys, do this:
ssh-keygen -b 1024 -f ~/.ssh/id_rsa -t rsa -N ""                             

...and it will display a few messages, and tell you that it created the
public / private key pair. You will see these files, id_rsa and,
in the /home/wolf/.ssh directory.

Copy the file into a file called "authorized_keys" right there in
the .ssh directory. We will be using this file later. Verify that the
contents of this file show the hostname [the reason we rebooted the box].
Modify the security on the files, and the directory:
chmod 644 ~/.ssh/auth*                                                       
chmod 755 ~/.ssh                                                             

According to the LAM user group, only the head node needs to log on to the
slave nodes; not the other way around. Therefore when we copy the public key
files, we only copy the head node's key file to each slave node, and set up
the agent on the head node. This is MUCH easier than copying all
authorized_keys files to all nodes. I will describe this in more detail

Note: I only am documenting what the LAM distribution of the message passing
interface requires; if you chose another message passing interface to build
your cluster, your requirements may differ.

At the end of /home/wolf/.bash_profile, add the following statements [again
this is lam-specific; your requirements may vary]:
export LAMRSH='ssh -x'                                                       
ssh-agent sh -c 'ssh-add && bash'                                            

4.7. MPI

Lastly, put your message passing interface on the box. As stated in 1.2
Requirements, I used lam. You can get lam from here:


...but you can use any other message passing interface or parallel virtual
machine software you want. Again, I am showing you what worked for me.

You can either build LAM from the supplied source, or use their precompiled
RPM package. It is not in the scope of this document to describe that; I just
got the source and followed the directions, and in another experiment I
installed their rpm. Both of them worked fine. Remember the whole reason we
are doing this is to learn; go forth and learn.

You may also read more documentation regarding LAM and other message passing
interface software [
Scientific-Computing-with-GNU-Linux/systems.html] here.

5. Set Up Slave Nodes

Get your network cables out. Install Linux on the first non-head node. Follow
these steps for each non-head node.

5.1. Base Linux Install

Going with my example node names and IP addresses, this is what I chose
during setup:
auto partition                                                               
remove all partitions on system                                              
use LILO as the boot loader                                                  
put boot loader on the MBR                                                   
host name wolf01                                                             
ip address                                                     
add the user "wolf"                                                          
same password as on all other nodes                                          
NO firewall                                                                  

The ONLY package installed: network servers. Un-select all other packages.

It doesn't matter what else you choose; this is the minimum that you need.
Why fill the box up with non-essential software you will never use? My
research has been concentrated on finding that minimal configuration to get
up and running.

Here's another very important point: when you move on to an automated install
and config, you really will NEVER log in to the box. Only during setup and
install do I type anything directly on the box.

5.2. Hardware

When the computer starts up, it will complain if it does not have a keyboard
connected. I was not able to modify the BIOS, because I had older discarded
boxes with no documentation, so I just connected a "fake" keyboard.

I am in the computer industry, and see hundreds of keyboards come and go, and
some occasionally end up in the garbage. I get the old dead keyboard out of
the garbage, remove JUST the cord with the tiny circuit board up there in the
corner, where the num lock and caps lock lights are. Then I plug the cord in,
and the computer thinks it has a complete keyboard without incident.

Again, you would be better off modifying your bios, if you are able to. This
is just a trick to use in case you don't have the bios program.

5.3. Post Install Commands

After your newly installed box reboots, log on as root again, and...

  * do the same chkconfig commands stated above to set up the right services.

  * modify hosts; remove "wolfnn" from localhost, and just add wolfnn and

  * install lam

  * create the /mnt/wolf directory and set up security for it.

  * do the ssh configuration

Up to this point, we are pretty much the same as the head node. I do NOT do
the modification of the exports file.

Also, do NOT add this line to the .bash_profile:
sh -c 'ssh-add && bash'                                                      

5.4. SSH On Slave Nodes

Recall that on the head node, we created a file "authorized_keys". Copy that
file, created on your head node, to the ~/.ssh directory on the slave nodes.
The HEAD node will log on the all the SLAVE nodes.

The requirement, as stated in the LAM user manual, is that there should be no
interaction required when logging in from the head to any of the slaves. So,
copying the public key from the head node into each slave node, in the file
"authorized_keys", tells each slave that "wolf user on wolf00 is allowed to
log on here without any password; we know it is safe."

However you may recall that the documentation states that the first time you
log on, it will ask for confirmation. So only once, after doing the above
configuration, go back to the head node, and type ssh wolfnn where "wolfnn"
is the name of your newly configured slave node. It will ask you for
confirmation, and you simply answer "yes" to it, and that will be the last
time you will have to interact.

Prove it by logging off, and then ssh back to that node, and it should just
immediately log you in, with no dialog whatsoever.

5.5. NFS Settings On Slave Nodes

As root, enter these commands:
cat >> /etc/fstab                                                            
wolf00:/mnt/wolf /mnt/wolf nfs rw,hard,intr 0 0                              
<control d>                                                                  

What we did here was automatically mount the exported directory we put in the
/etc/exports file on the head node. More discussion regarding nfs later in
this document.

5.6. Lilo Modifications On Slave Nodes

Then modify /etc/lilo.conf.

The 2nd line of this file says

Modify that line to say:

After it is modified, we invoke the changes. You type "/sbin/lilo", and it
will display back "added linux *" to confirm that it took the changes you
made to the lilo.conf file:
Added linux *                                                                

Why do I do this lilo modification? If you were researching Beowulf on the
web, and understand everything I have done so far, you may wonder, "I don't
remember reading anything about lilo.conf."

All my Beowulf nodes share a single power strip. I turn on the power strip,
and every box on the cluster starts up immediately. As the startup procedure
progresses, it mounts file systems. Seeing that the non-head nodes mount the
shared directory from the head node, they all will have to wait a little bit
until the head node is up, with NFS ready to go. So I make each slave node
wait 2 minutes in the lilo step. Meanwhile, the head node comes up, and
making the shared directory available. By then, the slave nodes finally start
booting up because lilo has waited 2 minutes.

6. Verification

All done! You are almost ready to start wolfing.

Reboot your boxes. Did they all come up? Can you ping the head node from each
box? Can you ping each node from the head node? Can you ssh? Don't worry
about doing ssh as root; only as wolf. Also only worry about ssh from the
head to the slave, not the other way around.

If you are logged in as wolf, and ssh to a box, does it go automatically,
without prompting for password?

After the node boots up, log in as wolf, and say "mount". Does it show
wolf00:/mnt/wolf mounted? On the head node, copy a file into /mnt/wolf. Can
you read and write that file from the slave node?

This is really not required; it is merely convenient to have a common
directory reside on the head node. With a common shared directory, you can
easily use scp to copy files between boxes. Sterling states in his book, on
page 119, a single NFS server causes a serious obstacle to scaling up to
large numbers of nodes. I learned this when I went from a small number of
boxes up to a large number.

7. Run A Program

Once you can do all the tests shown above, you should be able to run a
program. From here on in, the instructions are lam specific.

Go back to the head node, log in as wolf, and enter the following commands:
cat > /nnt/wolf/lamhosts                                                     
<control d>                                                                  

Go to the lam examples directory, and compile "hello.c":
mpicc -o hello hello.c                                                       
cp hello /mnt/wolf                                                           

Then, as shown in the lam documentation, start up lam:
[[email protected] wolf]$ lamboot -v lamhosts                                      
LAM 7.0/MPI 2 C++/ROMIO - Indiana University                                 
n0<2572> ssi:boot:base:linear: booting n0 (wolf00)                           
n0<2572> ssi:boot:base:linear: booting n1 (wolf01)                           
n0<2572> ssi:boot:base:linear: booting n2 (wolf02)                           
n0<2572> ssi:boot:base:linear: booting n3 (wolf04)                           
n0<2572> ssi:boot:base:linear: finished                                      

So we are now finally ready to run an app. [Remember, I am using lam; your
message passing interface may have different syntax].
[[email protected] wolf]$ mpirun n0-3 /mnt/wolf/hello                              
Hello, world! I am 0 of 4                                                    
Hello, world! I am 3 of 4                                                    
Hello, world! I am 2 of 4                                                    
Hello, world! I am 1 of 4                                                    
[[email protected] wolf]$                                                          

Recall I mentioned the use of NFS above. I am telling the nodes to all use
the nfs shared directory, which will bottleneck when using a larger number of
boxes. You could easily copy the executable to each box, and in the mpirun
command, specify node local directories: mpirun n0-3 /home/wolf/hello. The
prerequisite for this is to have all the files available locally. In fact I
have done this, and it worked better than using the nfs shared executable. Of
course this theory breaks down if my cluster application needs to modify a
file shared across the cluster.